background image

R

epair

[3] DISASSEMBLY/ASSEMBLY

[3] -5. Gear section

P 11/ 18

Fig. 15

(1) Disassemble Safety cover as drawn in 

Fig. 8

.

(2) Remove Bearing box section from Blade case, then disassemble Gear section as drawn in 

Fig. 15

.

DISASSEMBLING

1. Remove two M5x16 Pan head screws,

    then disassemble Bearing box from

    Blade case.

2. Remove Ball bearing

    606ZZ with 1R269.

3. Remove Retaining ring S-12

     with 1R291.

4. Fix Bearing box in Vise as shown below. Then, fit the pins of 1R316 to the notches of Bearing retainer 19-29

    and remove the retainer by turning 1R316 counterclockwise.

Ball bearing 606ZZ

Bearing box

Retaining

ring S-12

M5x16 Pan head

screw (2 pcs.)

Bearing retainer 19-29

Bearing 

retainer 19-29

1R316

Helical gear 50

5. Put Bearing box onto 1R232. then,

    put 1R032 onto Helical gear 50

    and give shock with Arbor press.

6. Applying 1R282 onto Spindle, push 1R282 with Arbor press.

    Spindle is removed from Helical gear 50, and Sleeve 12 is separated.

    Then, remove Ball bearing 6001DDW from Spindle with 1R269.

1R232

Notch

1R032

1R282

Spindle

Sleeve 12

Helical gear 50

Ball bearing

 6001DDW

Assemble Gear section by reversing the disassembly procedure. (Refer to 

Fig. 15

.)

ASSEMBLING

Summary of Contents for DHS680



















Reviews: