background image

[3] DISASSEMBLY/ASSEMBLY

[3]-5. Impact bolt

DISASSEMBLING

(1) Disassemble the parts on the top of Tool holder section. (

Fig. 2 of page 5

) Remove Carbon brushes. (

Fig. 4 of page 5

)

(2) Remove Inner housing section from Gear housing complete, and separate Tool holder complete from Piston cylinder 

      (

Fig. 6 of page 6

)

(3) Remove Retaining ring WR-25, Flat washer 25, Compression spring 25 and Spur gear 46 from Tool holder. (

Fig. 10

 

of

      

of page 9

)

(4) Remove Ring spring 22 from Inner housing complete installation side of Tool holder complete. (

Fig. 18

)

      

Note

: Fitting of Ring spring 22 into the groove on inner surface of Tool holder complete is weaker than that of AC tool,

                and therefore, holding Ring spring 22 in a vise is not necessary. 

 (5) Remove Ring 11, Impact bolt and X ring 13 from Cap 35 installation side of Tool holder complete. (

Fig. 19

)   

Fig. 18

Fig. 19

2. Tap Ring spring 22 through the other hole of Tool holder 

     complete with a slotted screwdriver in the same way of

     the step 1.

3. Repeat 1 and 2 alternately.

1. Tap Ring spring 22 through the hole of Tool 

    holder complete with a slotted screwdriver 

    in direction of the gray arrow. 

Cap 35 installation

side

Inner housing complete 

installation side

Inner housing complete 

installation side

X ring 13

Ring 11

Impact bolt

Cap 35 installation

side

Inner groove of

Tool holder

Ring spring 22

off from inner 

groove

4. Pull off Ring spring 22 with pliers. 

Strike the inner housing complete installation side of

Tool holder complete against workbench to remove

Ring 11, X ring 13 and Impact bolt.

Ring spring 22

P 14/ 17

R

epair

Summary of Contents for DHR165


















Reviews: