ENGLISH
11
•
Over-voltage protection
When the input voltage is higher than the rated
YROWDJHWKLVSURWHFWLRQV\VWHPWXUQVRႇWKH
appliance and the temperature display shows "F4"
with beep sound.
•
Tilt protection function
The tilt protection function is valid when operating
the appliance in cooling mode. When the
appliance get equal to or greater than 30° from
OHYHODQJOHDVVKRZQ$%&RU'LQWKH¿JXUH
the appliance stops cooling and the temperature
display shows “F1” for a while. After the appliance
back in level position, it takes about 3 minutes to
restart.
Ź
Fig.4
Protections against other causes
Protection system is also designed for other causes that
could damage the appliance and allows the appliance to
stop automatically. Take all the following steps to clear
the causes, when the appliance has been brought to a
temporary halt or stop in operation.
7XUQWKHDSSOLDQFHRႇDQGWKHQWXUQLWRQDJDLQWR
restart.
2.
Charge the battery(ies) or replace it/them with
recharged battery(ies).
3. Let the appliance and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
USB charging
There is the USB port in the battery compartment. The
USB port continuously outputs 5V voltage in operation
state.
NOTICE:
Connect only devices which are
compatible with the USB power supply port.
Otherwise it may cause malfunction to the appliance.
NOTICE:
Do not connect the USB power supply
port of this appliance to the USB terminal of your
computer.
It may cause malfunction.
NOTICE:
Before connecting USB device to
the appliance, always backup your data of USB
device.
Otherwise your data may be lost by any
possibility.
NOTICE:
When not using devices or after
charging, remove the USB cable.
NOTE:
The appliance may not supply power to some
USB devices.
Memory function
After setting the control temperature, if the user does
not operate within 5 seconds, the current setting will be
memorized. Next time, the appliance starts in the same
setting.
Switching the unit of temperature
You can switch the unit of temperature °C (degree
Celsius) or °F (degree Fahrenheit) by following
procedure.
1. Turn on the appliance.
2. Press the cool / heat switch button until the unit
&RU)VWDUWVÀDVKLQJ
3. Press the temperature plus button or the
temperature reduction button to select unit.
4. Press the cool / heat switch button, or leave the
appliance 5 seconds without any operation. The
unit selection is completed.
Error code
)RUWKHVSHFL¿FHUURUVWKHWHPSHUDWXUHGLVSOD\VKRZV
following code.
Error code
Matter
F1
Tilt protection is active. Refer the section for
the tilt protection function.
F2
Running out of battery.
F3
Input voltage is low. Refer the paragraph for
the low-voltage protection.
F4
Input voltage is high. Refer the paragraph for
the over-voltage protection.
Error codes
other than
the above
7XUQRႇDQGUHVWDUWWKHDSSOLDQFH,IWKHHUURU
still does not improve, take the appliance to
Makita Authorized or Factory Service Centers.
MAINTENANCE
CAUTION:
Always be sure that the appliance
LVVZLWFKHGRႇXQSOXJJHGDQGWKHEDWWHU\
cartridge is removed before attempting to perform
inspection or maintenance.
CAUTION:
Do not spray or pour water on
the appliance when cleaning. Do not wash with a
hose; avoid getting water inside of the appliance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
UHSDLUVDQ\RWKHUPDLQWHQDQFHRUDGMXVWPHQWVKRXOG
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning
•
Clean the oil stain in the chamber regularly.
•
Clean around the interior of the chamber to
prevent odor.
&OHDQWKHGXVWRQWKHVSRQJH¿OWHUUHJXODUO\WR
LPSURYHWKHUHIULJHUDWLRQHႈFLHQF\
•
The sealing strip of the upper cover is easy to get
dirty, clean it in time.
