manualshive.com logo in svg

MAK M20, Operating Instructions Manual

Share
Download
MAK M20 Operating Instructions Manual Download Page 429

Lubricating Oil/Cooling Water Thermostat

Maintenance / Checking

 

A5.05.

 11.06.01.00

7500

M20-M601C

en / 31.05.2000

IB021739

2/2

11

Ĺ

1.6

Check lower seat and sealing faces of thermostatic element for damage.

1.7

Wipe clean thermostat housing with a lint-free rag and check for corrosion and deposits. 
Check upper plate for erosion.

2.

Functional Check of the Thermostatic Element

2.1

Put thermostatic element (1) into a water bath of a termpature of approx. 10 K above the 
mean temperature specified on the insert (XX) (specification in degree Fahrenheit).

2.2

The thermostatic element must open steadily.

3.

Assembly

3.1

Slightly grease inner side of O-ring (4) and upper face of element and regulating spindle. 
By the clearance of the O-ring, heat elongations are compensated.

3.2

Top up lubricating oil/cooling water system and check thermostat for leakage.

Summary of Contents for M20









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands