manualshive.com logo in svg

MAK M20, Operating Instructions Manual

Share
Download
MAK M20 Operating Instructions Manual Download Page 209

Exhaust Valve Cones

Repair / Checking

 

A5.05. 

01.08.01.03

M20

en / 12.10.2000

IB022666

3/5

01

Ĺ

2.

Cleaning

Clean the valve cone, e.g. blasting with 
glass beads. Cleaning with sharp-edged 
tools as well as pickling with inorganic 
acids (hydrochloric acid, sulphuric acid, 
hydrofluoric acid etc.) is not allowed.

3.

Repair (refinishing of the valve cone 
face)

Note: 

Refinishing should always be carried 
out professionally on precision spindle 
grinding machines. If no such machine 
is available, the valves should be given 
to a MaK workshop for regrinding.

3.1

Regrind valve cone faces in accordance 
with prescribed angle (

Fig. 3

). Do not 

refinish existing concave fillet.

3.2

The appropriate information of the 
grinding machine manufacturers is to 
be observed during grinding.

3.3

Determine the dimension between 
visible edge of the base metal plating 
“

X

” and the outer edge of the seat after 

completing the grinding process. 
Replace the valve cone if the actual 
dimension falls below the minimum 
dimension.

3.4

Outer edge rounded with stone.

Attention:

When the valve cone is refinished, the 
valve seat ring must also be refinished 
(01.08.02.nn).

Fig. 3

X

2

9

° 

5

2

' +

 2

'

min. 1 mm

Summary of Contents for M20









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands