manualshive.com logo in svg

MAK M20, Operating Instructions Manual

Share
Download
MAK M20 Operating Instructions Manual Download Page 383

Fuel Injector

Maintenance / Adjust

 

A5.05. 

07.08.01.00

M20

en / 03.06.1998

IB001410

1/2

07

Ĺ

See also:

07.07.01.nn, 07.09.01.nn

Spare parts list:

B1.05.07.2.2267

Time requirement:

1 Pers./ 0,50 h

Personnel qualification: skilled engine hand

----------------------------------------------------------------------------------------------------------------------

Operating medium:

Heavy fuel and distillate fuel

Tools:

Nozzle tester

W1

1.9470 B

Adapter/Nozzle holder - nozzle tester

W2

2.9208 A

Pressure pipe

W3

1.9470-51

ĭ

Safety note:

When checking the opening pressure: Danger! Keep your hands off the fuel jet!

Note:

Carbon trumpets at the nozzle are mostly caused by insufficient cooling. Corrosive attack 
and erosion, however, are the consequence if the nozzle temperature is too low. 
The charge air temperature may also be too low or water in the charge air. 

The perfect functioning of the injection nozzles can only be judged on the basis of the ex-
haust gas temperatures or the smoke emission.

The injection valve should only be inspected if there is a clear deviation of the exhaust gas 
temperature from the mean value.

With heavy fuel nozzles the cause of bad atomization on the test rig frequently is 
insufficient flushing of the injector with diesel oil. Before replacing the nozzle this should 
be cleaned and checked again very carefully. 

A drop in the opening pressure of up to 

20 bar

 after a short period of operation is normal 

(set of nozzle spring and needle).

Summary of Contents for M20









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands