background image

The Majestic Shower Company Limited

 

17 Flitch Industrial Estate, Chelmsford Road, 

Dunmow, CM6 1XJ 

Tel44 (0) 8448 001 500

 

Fac44 (0) 1279 635 074 [email protected] 

www.majesticshowers.com

 

 

 

Portofino Installation Guide 

Page 8

 

 

Cut the wall profiles to length using a Junior hacksaw 
and then file the cut ends smooth.

 

Run a bead of silicone along the wall side of the wall 
profiles and screw them tightly in place.

 

Loosely screw the Glass to Wall brackets to the wall.

 

Check that the rubber strips are correctly positioned.

 

Run beads of silicone along the inside of both vertical 
wall profiles as shown, and the underframe channels 
where the Return panel and In Line panel will sit.

 

Do not apply silicone to the underframe where the 
Insert will be fitted under the door. Place a generous 
amount of silicone into the bottom corners where the 
vertical profiles and underframe channels meet.

 

 

 

 

 

 

Using suction glass lifters, replace the glass Return 
panel and In Line panel into the silicone lined channels.

 

To prevent leakage around the wall brackets, fill the 
glass slots with silicone as shown.

 

Loosely fix the face plates of the glass to wall brackets 
through the slots in the glass, ensuring that the clear 
gaskets are inserted on both sides of the panel. Fully 
tighten the wall screws.

 

Ensure the Return panels are plumb vertical and in the 
correct position in the underframe, then fully tighten 
the glass to wall bracket face plates.

 

13

 

14

 

15

 

16

 

Summary of Contents for Portofino















Reviews: