PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
.25
Push-Touch Waste and Overflow
Installation Guidelines
Page 1 of 3
Rev - 02
9.18.2015
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 PUSH-TOUCH WASTE AND OVERFLOW (STYLE No.PTWO04), .25 FREESTANDING OVAL BATHTUB (STYLE
No. PTBT25), .25 REVERSE FREESTANDING OVAL BATHTUB (STYLE No. PTBT52), & COLETTE FREESTANDING
OVAL BATHTUB (STYLE No. CBBT01).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
STYLE No.
PTWO04
Code No.
WWDR04
RECOMMENDED FOR TUB(S):
PTBT25: .25 Freestanding Oval Bathtub
PTBT52: .25 Reverse Freestanding Oval Bathtub
CBBT01: Colette Freestanding Oval Bathtub
IMPORTANT:
Immediately after receiving the bathtub and removal of
packing, you MUST inspect the unit for freight damage.
Any claims for damage, whether apparent or hidden,
must be made to the carrier immediately in order for
them to assume all associated costs. Should inspection
reveal any defect in the finish, do not install the bath tub.
Damage or defect to the finish claimed after the bathtub
is installed is excluded from the warranty. The warranty
DOES NOT cover labor or materials to remove or reinstall
the bathtub.
To ensure this product is installed properly, you must
read and follow these guidelines.
The owner/user of the bathtub must keep this
information for future reference.
All final connections are made below the finished floor.
Accessibility below the finished floor is recommended.
For installations that have access from below the
finished floor, trap adapters can be used instead of the
slip joint gasket supplied.
For installations where access from below the finished
floor is limited, i.e. slabs, the slip joint gasket supplied is
required.
This product must be installed by a professional
licensed contractor. Be sure your installation conforms
to all federal, state, and local codes.
Refer to the specification and assembly drawings
attached.
Inspect this product to assure it is the correct model
and you have all parts required for proper installation.
Take all necessary precautions to ensure the tub is
protected during installation.
WASTE AND OVERFLOW ROUGH-IN NOTE:
A.
This drain fits a tub that has an internal overflow
channel built INSIDE the wall of the tub which is
similar in design and function as a lavatory sink. There
is not a drain shoe that is common on standard tub
drains.
B.
This drain does not use a cable or trip lever system to
operate the drain stopper. Instead, it uses a simple
pop-up drain that is closed and opened by pushing
down on the stopper.
1.
Clean the drain hole area in the bathtub in preparation
of setting the drain. The area should be dry and free
of any debris and oil.
2.
Cover the floor with a pad or other protective material
and gently rest the tub on its side to allow for drain
and overflow assembly.
3.
Dry fit the drain assembly.
a.
Place the drain collar (6) into the drain opening.
b.
Slide the lower gasket (8) and metal washer (8a)
onto the drain collar, thread on the locking nut (9)
then attach the tail piece (10-12).
4.
Determine the placement of the tub then mark the
floor at the center point of the drain opening.
5.
Drill a hole through the floor to accommodate the
drain.
6.
Rough in 1-1/2" DWV (not supplied). Assure all DWV
pipe and fittings are well supported to eliminate the
possibility of shifting.
7.
IMPORTANT:
Make sure the 1-1/2" hub is 1" - 3" to the
finished floor so the 5-3/4” tailpiece can be installed
securely. The slip joint gasket does not fit in a copper
coupling.
INSTALLATIONS THAT HAVE ACCESS FROM BELOW
THE FINISHED FLOOR:
WASTE AND OVERFLOW INSTALLATION
NOTE
: Installations that have access from below the
finished floor, trap adapters can be used instead of the
slip joint gasket supplied.
8.
Cover the floor with a pad or other protective material
and gently rest the tub on its side to allow for final
drain and overflow assembly.
9.
Unthread the stopper (5, 5a & 5b) from the drain
collar then slide the rubber gasket (7) onto the collar
then insert it into the drain opening. A bead of clear
adhesive silicone around the drain collar can be
applied instead of the rubber washer.
