Mahr Maxum III Instruction Manual Download Page 26 | Manualshive

Page: 26 / 56

background image

26

Maxuum III Digital Electronic Indicator 2239028 Rev D

segment. Enhanced functions using the FAN display (MIN, MAX

and TIR) require the user to depress the RESET button after

obtaining an on-scale reading. In Enhanced mode, the indicator

reacts like a traditional Maxum Plus, digital readings are

restored with any on-scale reading.

Figure 19 - Indicator shown in Over-Range condition

4.1.3 Standard Mode

This mode operates according to the traditional Maxum unit.

This is the normal static measuring mode and is indicated by a

normal static Fan display and no tolerance arrows when within

tolerance. If out of tolerance one of the arrows will be flashing.

4.1.4 Initial Setup - Standard/TSP Mode

This mode shows the actual position of the spindle in the Indi-

cator's measuring range. When True Spindle Position is acti-

vated, the Indicator's analog display changes to the alternate

mode, i.e. a normal Fan display changes to a Single Element dis-

play and vice-versa.
Use a ballpoint pen or similar pointed instrument to activate

switches. Do not use a pencil; graphite dust may affect button

switches.

1.

Mount the Indicator or Digital Transducer in the gage.

2.

Place the Nominal or Zero Master in the gage.

3.

Press and release the True Spindle Position (TSP)

button. Unit must be on-scale.

4.

Mechanically adjust the Indicator or Digital Transducer

until reading is at or near zero.

Securely lock the Indicator or Digital Transducer in position mak-

ing sure reading is still at or near zero.

«
...
24
25
26
27
28
...
»

Summary of Contents for Maxum III

























































Reviews:

No comments

Related manuals for Maxum III

Brand: Datalogic Pages: 6

Brand: Datakom Pages: 4

Brand: Datakom Pages: 38

Brand: ECO Sensors Pages: 22

Brand: ECO Sensors Pages: 7

Brand: F&F Pages: 24

Brand: Hardy Barth Pages: 27

CP-4900 Micro-GC

Brand: Varian Pages: 13

Brand: YOKOGAWA Pages: 16

Brand: Mini Pages: 20

Brand: AEMC Pages: 4

WALLACE & TIERNAN P7 ADVANCED

Brand: Evoqua Pages: 98

Brand: SAT-Kabel Pages: 12

Brand: Dakota Digital Pages: 34

Brand: Value Pages: 20

Brand: 3M Pages: 168

Brand: SEAWARD Electronic Pages: 57

Brand: Lafayette Instrument Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands