background image

Warnings

309226M

5

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system 
component. See 

Technical Data

 in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See 

Technical Data 

in all

 

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information 
about your material, request MSDS from distributor or retailer.

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine Graco 
replacement parts only.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your Graco distributor for information.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

PRESSURIZED ALUMINUM PARTS HAZARD 

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids 
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical 
reaction and equipment rupture, and result in death, serious injury, and property damage. 

TOXIC FLUID OR FUMES HAZARD 

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or 
swallowed.

Read MSDS’s to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

BURN HAZARD

Equipment surfaces can become very hot during operation. To avoid severe burns, do not touch hot 
equipment. Wait until equipment has cooled completely.

PERSONAL PROTECTIVE EQUIPMENT 

You must wear appropriate protective equipment when operating, servicing, or when in the operating 
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic 
fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eye wear 

Clothing and respirator as recommended by the fluid and solvent manufacturer

Gloves

Hearing protection

WARNING

Summary of Contents for 232735









































Reviews: