background image

Advanced Troubleshooting 

18

309226M

Building circuit breaker opens 
as soon as sprayer is plugged 
into outlet and sprayer is NOT 
turned on.

NOTE: 

Remove enclosure 

mounting screws and pull 
enclosure away from drive 
housing. Take care not to pull 
on leads from electrical cord 
and power switch.

Sprayer electrical cord is 
damaged.

1. Unplug sprayer electrical cord. 
2. Disconnect black electrical cord wire at 

power switch.

3. Unplug in-line connection white cord wire.
4. Plug in electrical cord.
5. Test voltage between black and white 

wires. Meter must read 85 to 130V AC.

6. Replace electrical cord if no voltage.

Sprayer power switch 
damaged.

1. Unplug sprayer electrical cord.
2. Disconnect black control board wire at 

power switch.

3. Check resistance of switch with ohmmeter.
4. Reading must be infinity with power switch 

OFF.

5. Reading must be zero with power switch 

ON.

6. Replace power switch if damaged.

Also see 

Basic Electrical Problems

 and 

Sprayer Wiring Problems

, page 16.

Specific Problem

Cause

Solution

General Problem: Erratic Motor Operation

Specific Problem

Cause

Solution

Sprayer quits after running for 
5 to 10 minutes

Electrical outlet is damaged

Reset building circuit breaker or replace building 
fuse. 

Electrical outlet supplying 
wrong voltage

Try another outlet. Check electric supply with volt 
meter. Meter must read 85 to 130V AC. If voltage 
is too high, do not use outlet until corrected.

Also see 

Basic Electrical Problems

 and 

Sprayer Wiring Problems

, page 16.

Motor is overheating

See Motor is Hot, page 14.

Motor is hot and runs 
intermittently.

See 

Basic Troubleshooting

, page 12.

Summary of Contents for 232735









































Reviews: