background image

Advanced Troubleshooting

309226M

21

General Problem: No Output

Specific Problem

Cause

Solution

Power switch is on and sprayer 
is plugged in but pump does 
not cycle

See 

Basic Troubleshooting

page 12.

Motor runs but pump does not 
cycle.

Gear and/or yoke are damaged 
(XR models only).

Replace gear and yoke using 

Gear/Yoke Repair 

Kit

, page 22.

Motor does not run.

Water or paint entered 
pressure control switch or 
shorted control board.

Clean out and/or dry out and retry. Replace if 
necessary using 

Pressure Control Switch Kit

page 22.

General Problem: Excessive Pressure Build Up

Specific Problem

Cause

Solution

Prime/Spray Valve actuates 
automatically, relieving 
pressure through drain tube.

Pressure control switch is 
worn.

Replace pressure control switch using 

Pressure 

Control Switch Kit

, page 22.

Water or paint entered 
pressure control switch or 
shorted control board.

Clean out and/or dry out and retry. Replace if 
necessary using 

Pressure Control Switch Kit

page 22.

Control board failed.

See 

Control Board Diagnostics

, page 24. 

Replace damaged control board using 

Control 

Board Kit

, page 22.

Summary of Contents for 232735









































Reviews: