background image

MAGNUM WINCHESTER « Elite » 

Corn/Biomass/Wood Pellet Stove  

Models: WIN-ACP & WIN-ACI,  

Owner’s Manual

 

 

Installation – Operation – Maintenance Instructions 

NOTE: THESE INSTRUCTIONS MUST BE SAVED for future reference 

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET 

BURNING STOVE.  FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY 

DAMAGE, BODILY INJURY OR EVEN DEATH. 

IMPORTANT: 

Always contact your local MagnuM dealer/installer with questions before contacting the 

factory.  When you call, have your serial number, purchase date, who installed the unit and a list of 
questions. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 
 
 
 

 
 
 
 
 

 
 

 

AMERICAN ENERGY SYSTEMS, INC. GRANTS NO WARRANTY, IMPLIED OR 

STATED, FOR THE INSTALLATION OR MAINTENANCE OF THE STOVE AND 

ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S). 

AMERICAN ENERGY SYSTEMS, INC. - 150 Michigan Street SE - HUTCHINSON, MINNESOTA 55350 

  

Web 

Site: 

www.MagnuMheat.com

 

9

 

When installing your 

MagnuM Winchester (WIN) Corn/Biomass/Wood Pellet

 stove, particular attention 

needs to be made in regards to fire protection.  If the unit is not properly installed, a house fire may result.  
For your safety, follow the installation and operation instructions provided, and if a question arises contact 
local building or fire officials about restrictions and installation requirements in your area. 

9

 

Read the operations and fuel section of this manual before plugging in your unit. 

9

 

Always unplug the unit before attempting any service work. 

9

 

Do not connect the unit to a chimney flue already serving another appliance. 

9

 

When installing the chimney pipe to the unit, it is important to remember that the unit operates on a 
negative pressure and the chimney on a positive pressure.  All chimney connections, elbows and fittings 
must be airtight.  

(Proper venting practices must be followed. Consult with a venting professional)

 

9

 

Ashes must be disposed of in a metal container with a tight fitting lid. 

9

 

All minimum clearances to combustibles must be followed. 

9

 

The 

MagnuM Corn/Biomass/Wood Pellet Stove 

is tested for operation with wood pellets, with an ash 

content of no more than 2% and Corn with a moisture content from 10-14 percent.  

It is recommended 

that wood pellets with an ash content of 1% or less be used for efficient operation of this unit. Higher 
ash content fuels will require additional maintenance and service.  Also, for use with wood pellets, 
cherry pits, olive pits or other pelletized Biomass fuel. Corn with 11-12 percent moisture is ideal.  

9

 

It is important to use fuel that is clean, dry and consistent.  

Make sure that your supplier is giving you 

the same fuel each time that you purchase.  It is recommended that you purchase your entire heating season 
supply of fuel at one time so that the fuel will be the same.

 

9

 

A voltage surge protector or ground fault outlet is required for this unit.  The electrical component 
warranty will be voided if surge protection is not installed before operating this unit.   

9

 

A grounded outlet must be provided with proper polarity.  A constant 120 volt (12volt on DC 
models), 60 cycles must be provided for proper operation or the warranty of this appliance will be 
forfeited.  

9

 

Special attention needs to be taken to clean out the top heat exchangers of this unit on a regular 
basis.  The fly ash settles on the heat exchangers and must be cleaned off to keep the unit operating 
properly.  Check for plugging every two-four weeks or when needed. 

9

 

If unit is not operated for extended periods of time (like summer) unplug the unit and disconnect the 
battery to assure long life of electrical components. 

Summary of Contents for Elite WIN-ACI


















































Reviews: