Magnetrol Pulsar R86 Installation & Maintenance Instructions Manual Download | Manualshive

Page: 31 / 61

background image

30

58-641 PULSAR Model R86 Pulse Burst Radar Transmitter - F

OUNDATION

fieldbus

™

Instruction Manual

IN_2

: The block input value and status.

IN_3

: The block input value and status.

IN_4

: The block input value and status.

DISABLE_1

: Parameter to switch off the input from being

used 0- Use, 1 - Disable.

DISABLE_2

: Parameter to switch off the input from being

used 0- Use, 1 - Disable.

DISABLE_3

: Parameter to switch off the input from being

used 0- Use, 1 - Disable.

DISABLE_4

: Parameter to switch off the input from being

used 0- Use, 1 - Disable.

SELECT_TYPE

: Determines the selector action; First

good, Minimum, Maximum, Middle, Average.

MIN_GOOD

: The minimum number of inputs which are

“good” is less than the value of MIN_GOOD then set the
OUT status to “bad”.

SELECTED

: The integer indicating the selected input

number.

OP_SELECT

: An operator settable parameter to force a

given input to be used.

UPDATE_EVT

: This alert is generated by any change to

the static data.

BLOCK_ALM

: The block alarm is used for all configura-

tion, hardware, connection failure, or system problems in
the block.

BLOCK_ERR_DESC

: Reports more specific details regard-

ing some errors reported through BLOCK_ERR.

3.4

Signal Characterizer Block (SC)

The Signal Characterizer (SC) function block characterizes
or approximates any function that defines an input/output
relationship. The function is defined by configuring as
many as 21 X, Y coordinates. The block interpolates an out-
put value for a given input value using the curve defined by
the configured coordinates. Two separate analog input sig-
nals can be processed simultaneously to give two corre-
sponding separate output values using the same defined
curve.

ST_REV

: The revision level of the static data associated

with the function block. The revision value will be incre-
mented in each time a static parameter value in the block is
changed.

«
...
29
30
31
32
33
...
»

Summary of Contents for Pulsar R86






























































Reviews:

No comments

Related manuals for Pulsar R86

Brand: Fairhaven Pages: 31

Brand: Samyung ENC Pages: 23

Satellite Radio

Brand: Raritan Pages: 2

Brand: SOUNDMASTER Pages: 38

Brand: Muse Pages: 15

DRS12AX X-Class

Brand: Furuno Pages: 52

Brand: Whistler Pages: 5

Brand: Samsung Pages: 2

Smart MBS RRH-C2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 60

Brand: Samsung Pages: 66

Smart MBS RRH-C2A

Brand: Samsung Pages: 80

Brand: Samsung Pages: 100

Brand: Berner Pages: 141

FreeMile Series

Brand: SAF Pages: 91

Brand: Clint Pages: 30

Brand: Star Microwave Pages: 31

Brand: Decatur Electronics Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands