Magnetrol Pulsar R86 Installation & Maintenance Instructions Manual Download

Page: 10 / 61

58-641 PULSAR Model R86 Pulse Burst Radar Transmitter - F

OUNDATION

fieldbus

™

Instruction Manual

2.2

Resource Block

The RESOURCE BLOCK describes the characteristics of
the F

OUNDATION

fieldbus

™

device such as the device name,

manufacturer, and serial number. As it only contains data
specific to the PULSAR Model R86 FF transmitter, it has
no control function.

2.2.1 Resource Block Parameters

MODE_BLK

: Must be in AUTO in order for the remain-

ing function blocks in the transmitter to operate.

NOTE: A Resource Block in “out of service” mode will stop all function

block execution in the transmitter.

RS_STATE

: Identifies the state of the RESOURCE block

state machine. Under normal operating conditions, it
should be “On-Line.”

DD_RESOURCE

: A string identifying the tag of the

resource that contains the Device Description for this
device.

MANUFAC_ID

: Contains Magnetrol International’s

OUNDATION

fieldbus

™

manufacturer’s ID number, which is

0x000156.

DEV_TYPE

: The model number of the PULSAR Model

R86 FF transmitter (0x0008). It is used by the Host System
and other fieldbus interface devices to locate the Device
Descriptor (DD) file.

DEV_REV

: Contains the device revision of the PULSAR

Model R86 FF transmitter and is used by the Host System
and other fieldbus interface devices to correctly select the
associated DD.

DD_REV

: Contains the revision of the DD associated with

the device revision of the PULSAR Model R86 FF transmit-
ter. It is used by the Host System and other Fieldbus inter-
face devices to correctly select the associated DD.

GRANT_DENY

: Options for controlling access of host

computer and local control panels to operating, tuning and
alarm parameters of the block.

HARD_TYPES

: The types of hardware available as channel

numbers.

RESTART

: Default and Processor are the available selec-

tions. Default will reset the Model R86 to the default
function block configuration.

NOTE: As RESTART DEFAULT will set most function block configura-

tion parameters to their default values. Devices need to be
reconfigured following activation of this function.

Summary of Contents for Pulsar R86






























































Search results

Summary of Contents for Pulsar R86

Reviews:

Related manuals for Pulsar R86

Brands by name

Popular brands

Magnetrol Pulsar R86, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for Pulsar R86

Reviews:

Related manuals for Pulsar R86

Brands by name

Popular brands