Magnetrol Pulsar R86 Installation & Maintenance Instructions Manual Download

Page: 29 / 61

IN_LO

: Input of the low range transmitter, in a range

extension application.

IN–1, IN–2, IN–3

: Inputs combined with the PV in a

section of four term math functions.

RANGE_HI

: Constant value above which the range exten-

sion has switch to the high range transmitter.

RANGE_LO

: Constant value below which the range exten-

sion has switch to the high range transmitter.

BIAS_IN_1

: The bias value for IN_1.

GAIN_IN_1

: The proportional gain (multiplier) value for

IN_1.

BIAS_IN_2

: The bias value for IN_2.

GAIN_IN_2

: The proportional gain (multiplier) value for

IN_2.

BIAS_IN_3

: The bias value for IN_3.

GAIN_IN_3

: The proportional gain (multiplier) value for

IN_3.

COMP_HI_LIM

: Determines the high limit of the com-

pensation input.

COMP_LO_LIM

: Determines the low limit of the com-

pensation input.

ARITH_TYPE

: The set of nine arithmetic functions

applied as compensation to or augmentation of the range
extended input.

BAL_TIME

: Specifies the time for a block value to match

an input, output, or calculated value or the time for dissipa-
tion of the internal balancing bias.

BIAS

: The bias value is used to calculate the output.

GAIN

: The gain value is used to calculate the output.

OUT_HI_LIM

: The maximum output value allowed.

OUT_LO_LIM

: The minimum output value allowed.

UPDATE_EVT

: This alert is generated by any changes to

the static data.

BLOCK_ALM

: Used for all configuration, hardware, con-

nection failure, or system problem in the block.

BLOCK_ERR_DESC

: Reports more specific details regard-

ing some errors reported through BLOCK_ERR.

58-641 PULSAR Model R86 Pulse Burst Radar Transmitter - F

OUNDATION

fieldbus

™

Instruction Manual

Summary of Contents for Pulsar R86






























































Search results

Summary of Contents for Pulsar R86

Reviews:

Related manuals for Pulsar R86

Brands by name

Popular brands

Magnetrol Pulsar R86, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for Pulsar R86

Reviews:

Related manuals for Pulsar R86

Brands by name

Popular brands