background image

       1-800-MAGLINE (624-5463) 

 

 

 Page 16                                               www.magliner.com

CooLift

®

Other Charger LED Indicators

These two orange power lights can mean 2 possible things.

1.  Press buttons 1 and 2 until the desired mode light is illuminated. The correct mode for your model 

is stated below.

2.  There is an error in the connection with the batteries. This will show when the charger cannot read 

a connection between the batteries, and pressing buttons 1 & 2 do nothing. Possible causes are 

loose terminal(s), wire or fuse disconnect, or a faulty battery bank. If lights light up, this means that 

power is being supplied to the charger, but not to the batteries. 

The white lights indicate the mode the charger is in either 12V Standard, AGM, Lithium or repair 

mode. The modes are selectable using buttons 1 & 2 once the charger is plugged in and the orange 

icons light up. Below are the following modes, and which mode should be selected. 

•  12V Standard is used for a general range of battery types. 

Select this mode for CooLift 

models with propulsion assist (models beginning in CPA).

•  AGM mode used for certain AGM batteries.

•  Lithium mode is for lithium batteries (not available for CooLift units).

• 

Repair mode will be used if a battery is showing less than 1 volt. Repair mode will not fix all 

battery problems. To use repair mode, hold down buttons 1 & 2 for at least 3 seconds. 

Summary of Contents for CooLift CPA43HTC































Reviews: