background image

       1-800-MAGLINE (624-5463) 

 

 

 Page 15                                               www.magliner.com

CooLift

®

Using the AC Charging Unit

Note:

  

A completely drained 40Ah battery can take up to 8 hours to fully charge. 

1.  To charge the CooLift, connect the AC charger plug to an AC outlet (120v domestic or 230v 

international).

2.  The batteries may be charged as often as desired. Magline recommends charging at least once 

after each delivery route is complete.

 

NOTE:  Each positive and negative wire from each charging bank has a 7.5A fuse.  

AC Charging Unit LED Indicators

The flashing red lights indicate the charging phase while the batteries are charging.

• 1 bar = 0-25% charged. The light will turn solid when 25% charge is reached, and the next light 

will begin to flash.

• 2 bars = 25-50% charged. The light will turn solid when 50% charge is reached, and the next light 

will begin to flash.

• 3 bars = 50-75% charged. The light will turn solid when 75% charge is reached and the next light 

will begin to flash.

• Flashing green light + 3 red light = 75-95%, this DOES NOT mean fully charged. 

• 

Maintenance mode (flashing green + 0 red lights) = 95-100%, means battery is optimizing the 

charge going into the battery, which ensures the battery is not overcharged. This prolongs battery 

life.

• Solid Green light = 100% fully charged

Charging notes: 

If batteries are fully charged and the charger is plugged in, the charger light will run 

through the entire cycle (1 red bar, 2 red bars, 3 red bar etc). This can take up to 3-5 minutes to go 

through the cycle; do not assume the charger did not charge the batteries. The charger constantly 

reads the batteries to determine optimal charging behavior.  Wait several minutes for the charger to 

properly read the batteries.

Summary of Contents for CooLift CPA43HTC































Reviews: