Magigoo Coater User Manual Download Page 18 | Manualshive

Page: 18 / 24

background image

Magigoo

Coater

User Manual

18

3.3 Adhesive compatibility

The Magigoo Coater should be used only with adhesives produced by Thought3D under the
brand Magigoo or other Thought3D approved adhesives.

Magigoo Coater has been designed to work with Magigoo and Magigoo Pro 3D printing build
plate adhesives. For more information on how to get the best performance out of Magigoo
adhesive products refer to User Manual for Magigoo Products (www.magigoo.com/tested-
materials) “GETTING MOST OUT OF MAGIGOO PRODUCTS”.

For safety, always read the Safety Data Sheet for each glue type before use.

Table of adhesives and material compatibility and performance.

Adhesive

Material

Magigoo Original Standard Adhesive

PLA, ABS, PETG, HIPS, TPU

Magigoo Pro PP

Polypropylene

Magigoo Pro PC

Polycarbonate

Magigoo Pro PA

Nylon

Surface

Original

PC

PA

PP

Regular Glass

Good

OK

Acceptable

Good

Borosilicate Glass

Good

OK

OK

Good

PEI

Good

Good

OK

Good

For more information about Magigoo adhesives see our manual and tested materials

database on www.magigoo.com/tested-materials, “TESTED MATERIALS” and “GETTING

MOST OUT OF MAGIGOO PRODUCTS” respectfully or reach out to [email protected].

«
...
16
17
18
19
20
...
»

Summary of Contents for Coater

























Reviews:

No comments

Related manuals for Coater

Brand: Ecco Pages: 4

Brand: JD Squared Pages: 15

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: Zenbooth Pages: 60

Brand: Xo Pages: 59

Brand: Falcon Pages: 8

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: Macht Dental Pages: 8

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: ABB Pages: 154

Brand: RAM Pages: 4

Brand: Ignis Pixel Pages: 4

Brand: Faro Pages: 161

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands