Magigoo Coater User Manual Download | Manualshive

Page: 17 / 24

background image

17

Instructions for Use

How to clean manifold:

2.

Place the assembled manifold into a bottle with water.

3.

Pump at least 15 times or until the water coming out looks clean.

Water may spray in different directions.

If the Coater will not be in use for longer period of time, clean the thin film applicator, valves

and the manifold properly, dismantle and store away in its case.

3.2.5

Cleaning Build Plate from Magigoo

Refer to 3.2.1. Cleaning the build plate.

1.

Remove the adhesive bottle and close with a cap.

!

Do not use hot water. Boiling

or hot water may damage

the bottle for water or the

applicator system.

«
...
15
16
17
18
19
...
»

Summary of Contents for Coater

























Reviews:

No comments

Related manuals for Coater

Brand: PANDROL Pages: 36

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: made for movement Pages: 51

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: Major Pages: 52

Brand: Jacobsen Pages: 20

Brand: M-system Pages: 5

Brand: MA Pages: 2

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Landoll Pages: 144

Brand: Castellini Pages: 299

Brand: Lowenstein Medical Pages: 457

GrainLogix XLB10

Brand: LOFTNESS Pages: 104

PRO-FORM ab GLIDER

Brand: ICON Health & Fitness Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands