background image

 

4

 

 

Indications of Icons 

Icon Indication 

Battery Low 

Battery 

Capacity 

Wave 

Vibration 

Hood 

Hood Open or Trigger 

Car Siren   

Mute Mode 

Parking Light   

Parking Light Flash 

Hammer 

Trigger of the First or Second Stage Shock Sensor 

Zzzzz Power 

Saving 

Mode

 

 

Trunk 

Trunk Open or Trigger 

Exhaust Fumes 

Engine Remote Start 

Door 

Door Open or Trigger 

Lock/Unlock Arm/Disarm 

 

System Features 

Remote Transmitter Code Learning 

  Take the following procedures to perform the transmitter code learning.   
a. Under the disarm mode, close the door, switch the ignition               

 

 

On 

ON/OFF 3 times and then, stay ON position.  

 

 

 

 

Off 

(each time shall get finished within 1second or it will 
skip this mode).   
Siren will chirp 2 times, and enter into the code learning  

 

 

 

 

 

 

Start 

mode. 

b. To perform the transmitter code learning, press button (1) within 10 seconds. 

Then the siren will chirp twice and the parking lights flash twice to confirm that the code has been learned. 
Take the same procedure for second, third and forth remote transmitter.   

b. If the ignition is turned OFF or button (1) is not pressed within 10 seconds, the system will quit the code learning mode. 

If so, try it again from the first step. 

c. Up to 4 remote transmitters are programmable to the system.     

www.shieldtechsecurity.com

Summary of Contents for FAI-8100













Reviews: