Magic-Pak MGE4-09-18 Installation And Maintenance Instructions Manual Download Page 3

506326-01

Page 3  of  20

Issue 0941

 Minimum Clearances

Figure 1

Top View

Clearance to combustible materials is 0" at the side, top, and front of plenum. If accessibility clearances are
greater than clearances to combustibles, accessibility clearances take precedence.

The front of the unit must be accessible for service. If the unit is enclosed, providing a door or access panel
opposite the front of the unit is the preferred method of providing access. The door or access panel must be
at least 30" wide (centered on the unit) and as tall as the unit.

IMPORTANT

The unit must be installed with approved wall sleeve and grille accessories for safe operation. Improper installa-

tions could result in property damage, personal injury, or death.

* Minimum clearance to combustibles for the front

of the unit is 1". Added clearance must be
provided for the gas supply line and drain trap
installation.

1"

Min.

1"

Min.

Front of Unit

Clearance to
Front of Unit*

Plenum

Exterior Wall

Wall Sleeve

(one each side)

Interior Wall

Clearances*

Mounting Strap
(one each side)

3/4" Plywood Riser

Floor

Platform (field supplied) - Must be level with sill plate of hole in exterior wall

4" Min.

Front of Unit

Sill Plate

Side View

unit must be supported by platform

Summary of Contents for MGE4-09-18





















Reviews: