background image

506326-01

Page 1  of  20

Issue 0941

Save these instructions for future reference

Installation and servicing of air conditioning equipment

can be hazardous due to internal refrigerant pressure

and  live  electrical  components.    Only  trained  and

qualified service personnel should install or service this

equipment.    Installation  and  service  performed  by

unqualified  persons  can  result  in  property  damage,

personal injury, or death.

  WARNING

Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.

Refer to this manual.  For assistance or additional information, consult a qualified installer, service agency,

or the gas supplier.

WARNING

The unit must be installed with approved wall sleeve and

grille  accessories  for  safe  operation.    Improper

installations could result in property damage, personal

injury, or death.

  WARNING

The installation of this appliance must conform to the requirements of the National Fire Protection Association; the National

Electrical Code, ANSI/NFPA No. 70 (latest edition) in the United States; the Canadian Electrical Code Part 1, CSA 22.1

(latest edition) in Canada; and any state or provincial laws or local ordinances.  Local authorities having jurisdiction should

be consulted before installation is made.  Such applicable regulations or requirements take precedence over the general

instructions in this manual.

 CAUTION

TABLE OF CONTENTS

INSTALLATION ....................................................2
START-UP ..........................................................12
OPERATION ......................................................13
MAINTENANCE .................................................16
ACCESSORIES..................................................17
WIRING DIAGRAMS ..........................................19

Manufactured By

Allied Air Enterprises, Inc.

A Lennox International Inc. Company

215 Metropolitan Drive

West Columbia, SC  29170

*506326-01*

For your safety, do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or

any  other  appliance.    Such  actions  could  result  in

property damage, personal injury, or death.

  WARNING

Installation and Maintenance Instructions

MGE4 Series

Gas Heating with Electric Cooling Unit

Summary of Contents for MGE4-09-18





















Reviews: