MADRIX LUNA 16 Page 81 User Manual Download

Page: 81 / 115

[Part 4] Technical Support

//81

www.madrix.com

MADRIX LUNA User Manual

LUNA Firmware

1.01.4555

MADRIX Version

MADRIX 3.1

Release Date

November 2013

Improved functionality and communication with the MADRIX 3 Software.

LUNA Firmware

1.02.4946

MADRIX Version

MADRIX 3.2

Release Date

March 2014

Added support for LUNA 4 and LUNA 16 in addition to LUNA 8.

LUNA Firmware

1.03.5043

MADRIX Version

MADRIX 3.3

Release Date

November 2014

Optimized device reply time (Poll Reply) to ensure that all connected devices are
found when searching for them automatically in MADRIX 3.

Fixed an issue that would reset the network settings with the next start when a
Subnet Mask higher than 255.255.255.0 was set up.

Fixed issues with sending out data when receiving Art-Net data from two sources.

Fixed an issue that only used the last of DMX output ports to send out data when
several ports had been assigned the same Art-Net universe.

LUNA Firmware

1.04.5298

MADRIX Version

MADRIX 3.3a

Release Date

December 2014

Fixed an issue that the IP address could not be changed using the web configuration
tool.

LUNA Firmware

1.05.5501

MADRIX Version

MADRIX 3.4

Release Date

June 2015

Fixed that the Poll Reply only returned 4 ports for LUNA 8 or LUNA 16.

LUNA Firmware

1.05.5997

MADRIX Version

MADRIX 3.6

Release Date

May 2016

All built-in status LEDs can now be switched off over Art-Net via ArtAdress.

Added support for ArtSync.

Summary of Contents for LUNA 16




















































































































Search results

Summary of Contents for LUNA 16

Reviews:

Related manuals for LUNA 16

Brands by name

Popular brands

MADRIX LUNA 16, User Manual

Search results

Summary of Contents for LUNA 16

Reviews:

Related manuals for LUNA 16

Brands by name

Popular brands