background image

 

SAFETY 

 

Form # 169089

 

4

 

Model Year - 2010

 

2 SAFETY 

 

2.1  SAFETY ALERT SYMBOL 

 
 
 
 
 
 
 
 
 
 

This safety alert symbol indicates important 
safety messages in this manual and on safety 
signs on the machine. 

 

This symbol means: 

 

ATTENTION! 
BECOME ALERT! 
YOUR SAFETY IS INVOLVED!

 

 

Carefully read and follow the safety message 
accompanying this symbol. 

 

WHY IS SAFETY IMPORTANT TO YOU? 

 

ACCIDENTS DISABLE AND KILL 
ACCIDENTS COST 
ACCIDENTS CAN BE AVOIDED 

2.2 SIGNAL 

WORDS 

Note the use of the signal words 

DANGER, 

WARNING,

 and

 CAUTION

 with safety 

messages. The appropriate signal word for each 
message has been selected using the following 
guidelines: 

 

DANGER 

Indicates an imminently hazardous 
situation that, if not avoided, will result in 
death or serious injury. 

 

WARNING 

Indicates a potentially hazardous situation 
that, if not avoided, could result in death or 
serious injury.  It is also used to alert 
against unsafe practices. 

CAUTION 

Indicates a potentially hazardous situation 
that, if not avoided, may result in minor or 
moderate injury. It is also used as a 
reminder of good safety practices. 

2.3 SAFETY 

SIGNS 

x

  Keep safety signs clean and legible at all 

times. 

x

  Replace safety signs that are missing or 

become illegible. 

x

  If original parts on which a safety sign was 

installed are replaced, be sure the repair 
part also bears the current safety sign. 

x

 

Safety signs are available from your Dealer 
Parts Department. 

2.3.1  Safety Sign Installation 

a.  Be sure the installation area is clean and dry. 

b.  Decide on the exact location before you remove 

the decal backing paper. 

c.  Remove the smaller portion of the split backing 

paper. 

d.  Place the sign in position and slowly peel back 

the remaining paper, smoothing the sign as it is 
applied. 

e.  Small air pockets can be smoothed out or 

pricked with a pin. 

Summary of Contents for R80









































































































Reviews: