background image

UNLOADING AND ASSEMBLY 

 

Form # 169078

 

 

Model Year - 2009

 

19 

B. A40-D HEADER 

The header drive connection only powers the 

knife and hay conditioner on the A40-D header 

(knife only on grass seed header).  Separate 

connections are required for the auger and reel 

as follows: 

a.  Route hoses (A) from tractor through support (B) 

and access hole (C) in header frame alongside 

existing hose bundle (D).   

b.  Remove cover on header electrical receptacle 

(E). 

c.  Push connector onto receptacle and turn collar 

on connector to lock it in place. 

d.  Attach cover to mating cover on tractor wiring 

harness. 

e.  Remove caps from hydraulic couplers and clean 

if necessary. 

f.  Push hose connectors onto mating receptacles 

as shown until collars on receptacles snap into 

lock position.   

g.  Open header L H drive shield. 

h.  Check hose routing at the reel motor and ensure 

it is as shown, depending on which tractor the 

header is being attached to.  Change hoses as 

shown  if  header is being mounted on a M100 

tractor. 

(continued next page) 

KNIFE & 

CONDITIONER 

PRESSURE 

CASE DRAIN 

KNIFE & 

CONDITIONER 

RETURN 

REEL &AUGER 

PRESSURE 

STANDARD HEADER 

GRASS SEED HEADER 

AUGER & REEL 

PRESSURE 

KNIFE PRESSURE 

(FEMALE FITTING 

AT HEADER) 

KNIFE RETURN 

(MALE FITTING 

AT HEADER) 

CASE DRAIN 

HOSE ROUTING – M150/M200 

(FACTORY CONFIGURATION) 

HOSE ROUTING – M100 

Summary of Contents for A30-S















































Reviews: