background image

BT/SN/RAM 6000 Series

 

Hardware Guide

1-11

Product Overview

Revised 2015-07-16

Specifications

*

+75°C See

 Thermal Performance and Considerations

 in Chapter 2.

Compliances

:

The BT/SN/RAM 6000 Series products meet the following standards plus others:

Electrical Safety

These devices have been designed to meet the basic safety requirements of the following 
standards:

CE per Low Voltage Directive and IEC 61010-1 (CE applies only to the -EU models. Please 
contact Red Lion for availability)

UL508 (Industrial control equipment), ANSI/ISA 12.12.01 (Hazardous Locations)

CSA C22.2 No. 142 and No. 213 (per cUL)

EMC (emissions and immunity) 

CE per the EMC directive (CE applies only to the -EU models. Please contact Red Lion for 
availability)

EN 301 489-1,-7,-24; EN 301 908-1,-2; EN 301 511: Immunity and Emissions.

FCC part 15 and ICES 003. See FCC statement on page 6.

EN 55022 (CISPR22)

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a commer-
cial environment. This equipment generates, uses, and can radiate radio frequency energy; 
and if not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference to radio communications, in which case the user will be 
required to correct the interference at their own expense. Warning: Changes or modifica-
tions to this unit not expressly approved by the party responsible for compliance could void 
the user's authority to operate the equipment. 

Information to the user: 

If this equipment causes interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the following measures: In order to 
meet FCC emissions limits, this equipment must be used only with cables that comply with 
IEEE 802.3. If necessary, the user should consult the dealer or an experienced radio/televi-
sion technician for additional suggestions. The user may find the following booklet pre-
pared by the Federal Communications Commission helpful: “How to Identify and Resolve 
Radio-TV Interference Problems”. This booklet is available from: U.S. Government Printing 
Office, Washington, DC 20402, Stock No. 004-000-00345-4

WEEE compliance

These devices comply with the WEEE directive. Do not throw away these devices in the 
standard trash. Contact Red Lion regarding proper disposal.

RoHS compliance

These devices comply with the RoHS directive and are considered lead and other hazardous 
substance free.

Summary of Contents for BT/SN/RAM 6000 Series

































Reviews: