M7EASDY
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-7763 Rev.5 P. 5 / 9
bration setting.
• Low Cut
1) Choose Input from the Set Up Transmitter and press Set
button.
2) Choose Low Cut and press Set button.
3) Use Up-Down buttons to choose the low-end cutout value
(0.00 to 99.99%) and press Set button.
4) Press Mode button to save the setting and exit the Low
Cut setting.
• Scaling (Engineering Unit & Decimal Point Position)
1) Choose Input from the Set Up Transmitter and press Set
button.
2) Choose Scaling and press Set button.
3) Engineering Unit
Choose Unit and press Set button.
4) Use Up-Down buttons to choose an unit from the selec-
tions (A, mA, V, mV, W, mW, %, °C, °F, Pa, kPa, MPa, User
Unit) and press Set button.
5) If User Unit is selected, an user-specific unit can be com-
posed on the display. Use Up-Down buttons to choose a
first character and press Set button to confirm and shift
the cursor to a next position. A second character can be
entered in the same manner, up to 10 characters.
6) Press Mode button to save the setting and exit the User
Unit setting.
7) Decimal Point Position
Choose Decimal Point and press Set button.
8) Use Up-Down buttons to choose an appropriate position
from the following selections:
0: 9999
1: 999.9
2: 99.99
3: 9.999
The decimal point is applied only to the display value.
9) Press Mode button to save the setting and exit the Deci-
mal Point setting.
• Scaling (Linearizer)
1) Linearizer
Choose Linearizer and press Set button.
2) Use Up-Down buttons to choose a function among: Linear
(proportional), Sqrt (square root extraction) and User Ta-
ble (segment linearization).
Linear or Sqrt
Specify 0% and 100% input values in engineering unit.
3) Use Up-Down buttons to choose 0% display value from
-9999 to +9999 and press Set button.
4) Use Up-Down buttons to choose 100% display value from
-9999 to +9999 and press Set button (Set to scaling 0% <
scaling 100%).
5) Press Mode button to save the setting and exit the Lin-
earizer setting.
User Table
Specify pairs of input % X and output values in engineer-
ing unit Y. Max. 128 points (pairs) are selectable (0 to 127)
Reverse setting is available.
3) Use Up-Down buttons to choose a calibration point and
press SET.
4) Use Up-Down buttons to choose an X value (-7.5 to
+107.5%) and press Set button.
5) Use Up-Down buttons to choose a corresponding Y value
from -9999 to +9999 and press Set button.
6) Press Mode button to save the setting and exit the Lin-
earizer setting.
ALARM SETTING
• Alarm Setpoints
1) Choose Alarm from the Set Up Transmitter and press Set
button.
2) Choose Setting Value and press Set button.
3) Use Up-Down buttons to choose L1 setpoint within the
display scale range and press Set button. Display unit is
indicated on the screen.
4) Use Up-Down buttons to choose L2 through L4 in the
same manner. Pressing Set button shifts the cursor posi-
tion to a next point.
5) Press Mode button to save the setting and exit the Set-
ting Value setting.
• Alarm Trip Actions
1) Choose Alarm from the Set Up Transmitter and press Set
button.
2) Choose Trip Operation and press Set button.
3) Use Up-Down buttons to choose Hi (High alarm trip) or
Lo (Low alarm trip) for the L1 setpoint and press Set but-
ton.
4) Use Up-Down buttons to choose trip actions for the L2
through L4 in the same manner. Pressing Set button
shifts the cursor position to a next point.
5) Press Mode button to save the setting and exit the Trip
Operation setting.
• Coil Energized or De-energized at Alarm
1) Choose Alarm from the Set Up Transmitter and press Set
button.
2) Choose Coil at Alarm and press Set button.
3) Use Up-Down buttons to choose Energize or De-energize
for the L1 setpoint and press Set button.
4) Use Up-Down buttons to choose coil type for the L2
through L4 in the same manner. Pressing Set button
shifts the cursor position to a next point.
5) Press Mode button to save the setting and exit the Coil at
Alarm setting.
POWER ON DELAY TIMER
1) Choose Power ON Delay Timer from the Set Up Trans-
mitter and press Set button.
2) Use Up-Down buttons to choose a delay time from 0 to 99
seconds and press Set button.
3) Press Mode button to save the setting and exit the Power
ON Delay Timer setting.
ALARM ON DELAY TIMER
1) Choose Alarm ON Delay Timer from the Set Up Trans-
mitter and press Set button.
2) Use Up-Down buttons to choose a delay time from 0 to
999 seconds and press Set button.
3) Press Mode button to save the setting and exit the Alarm
ON Delay Timer setting.
MOVING AVERAGE
1) Choose Moving Average from the Set Up Transmitter
and press Set button.
2) Use Up-Down buttons to choose a number of samples
from None (No average function), 4 samples, 8 samples,