background image

 

Page 6 

2.4

 

Initial Setup 

It is important to set up Hilo in the proper order to avoid any speaker damage calamities. Follow these steps for the best results: 

 

Connect the AC power cord to Hilo and to a quality, surge-protected AC power source. Check the Power and Safety section 
of this manual for additional information. 

 

Connect cables from Hilo to whatever audio devices Hilo will be connected to. These could include powered speakers, 
mixing consoles, power amps, microphone pre-amps, effects processors, etc.  

 

Make sure volumes are turned down on connected equipment to avoid excessive level being sent to the equipment during 
setup. 

 

If the context of use is as a standalone AD/DA converter that will not be connected to a computer, skip ahead to section 3, 
and in particular section 3.4.8: Output Mix Routing Page, for appropriate routing assistance. 

 

If using Hilo with a Mac or PC computer, follow the installation procedure below.   

2.5

 

Computer Set Up 

All driver files and utilities mentioned in the subsequent installation steps are available on our website at: 

http://www.lynxstudio.com 

> Support > Downloads  

If a previous driver version is present, it will automatically be removed as part of the driver installation process.  
 
Note: No driver installation is required for OS X or iOS, only for Windows. 

2.5.1

 

Driver Installation for Windows XP, Vista or Windows 7/8/10 

1.

 

Power on Hilo with the USB cable disconnected.  The Hilo driver should be installed prior to connecting the cable. 

2.

 

Download the most recent driver from the 

http://www.lynxstudio.com 

website and save the file to a convenient location. 

3.

 

Double-click the downloaded HiloSetup.exe file.  

 

 

 

4.

 

Click “Run” on the following screen to launch the 
installer. 

5.

 

Accept the “End User License Agreement” to 
proceed. 

 

 

6.

 

Click “Install” to accept the default directory for 
program files. 

7.

 

After some time the following prompt will appear to 
allow changes to your computer. Click “Yes” in 
order to proceed. 

 

 

8.

 

After some time, the Installation Wizard will 
appear. Choose “Next” to proceed. 
 

9.

 

After a pause, you will be prompted to connect the 
USB device. Connect the USB cable from the Hilo 
to a vacant USB 2.0 port on your computer. Then 
click “Next”. 

Summary of Contents for hilo

































































Reviews: