5
To enable/disable Master Raise/Lower from affecting
RGB/CMY zones (disabled by default)
1. After assigning RGB/CMY zones to the GRAFIK Eye
®
24FOUFS
programming mode on the GRAFIK Eye
®
QS and choose “Zone
Setup” from the Main Menu.
Select “RGB/CMY config”.
6TFUIF.BTUFS#VUUPOTUPDIPPTF
&OBCMFwPSi%JTBCMFw1SFTT0,UP
confirm.
3. Exit programming mode.
Color Programming Tool
The QSE-CI-DMX comes with a standard table of colors already
MPBEFE6TFSTDBONPEJGZUIFUBCMFUPBDIJFWFEFTJSFEDPMPST
1. Install the program from the enclosed CD.
$SFBUFBOFXQSPKFDUPSVTFUIFQSPWJEFEEFGBVMUDPMPSUBCMF
*GZPVBSFDSFBUJOHBOFXQSPKFDUZPVDBOFOUFSJOEJWJEVBMDPMPS
values in either RGB (red-green-blue) or CMY (cyan-magenta-
yellow) format. Values can be entered in either decimal or
IFYBEFDJNBMGPSNBU"EEJUJPOBMMZUIFJOUFSQPMBUFGVODUJPOXJMMGJMMJO
values automatically when you define the boundary values.
6TFUIFi5FTUwGFBUVSFPOUIFUJUMFCBSUPWJFXZPVSFEJUFEDPMPS
table.
$POOFDUBNJOJ64#DBCMFCFUXFFO
ZPVS1$BOEUIFNJOJ64#QPSU
under the bottom hinged door of
your GRAFIK Eye
®
QS.
6TFUIFi5SBOTGFSwDPNNBOEUP
either download your color table
JOUPUIF24&$*%.9PSUPFYUSBDU
a color table from a QSE-CI-DMX to
your PC for further editing.
OK
7
6
1
5
1
8
9-16
1-8
.JOJ64#QPSU
To unassign DMX channels from a GRAFIK Eye
®
QS:
1. Enter programming mode on the QSE-CI-DMX: Press and hold
UIFQSPHSBNNJOHCVUUPOGPSTFDPOET5IF4UBUVT-&%XJMM
CMJOLSBQJEMZ
2. The LEDs of the zones assigned to
DMX channels will be flashing full on.
5PVOBTTJHOQSFTTUIFEFTJSFE[POFT
lower button. Press OK to confirm
operation.
3. Exit programming mode: Press and hold the programming
button on the QSE-CI-DMX for 3 seconds. The yellow status
-&%XJMMCMJOLPODFQFSTFDPOE
Display Type Setup
5IFSFBSFUXPEJTQMBZUZQFTUPDIPPTFGSPNiEJTQMBZwXIJDI
EJTQMBZTMJHIUJOUFOTJUZBTBQFSDFOUBHFBOEiEJTQMBZw
which displays intensity as a numeric value. For RGB DMX
[POFTJUNBZCFEFTJSBCMFUPTFMFDUiEJTQMBZwJOPSEFSUP
step through each entry in the RGB/CMY table. This option is
available only after DMX channel assignment.
1. Enter programming mode on the GRAFIK Eye
®
24BOEDIPPTF
“Zone Setup” from the Main Menu. Select “Display type”. The
LEDs of the zones assigned to DMX channels will be flashing full
on.
6TFUIF[POFSBJTFMPXFSCVUUPOTUP
toggle between display types for each
zone. Press “OK” to confirm. Repeat
for all desired zones.
3. Exit programming mode.
Trim Setup
High and low end trim settings limit the maximum and minimum
output of a dimming zone. Follow the instructions below to
NBOVBMMZTFUUIFMFWFMTBTEFTJSFE
1. Enter programming mode on the GRAFIK Eye
®
24BOEDIPPTF
“Zone Setup” from the Main Menu. Select “High end” or “Low
end”. The LEDs of the zones assigned to DMX channels will
show the high end or low end intensity.
6TFUIF[POFSBJTFMPXFSCVUUPOTUP
set the desired trim levels. Repeat for
all desired zones and trims. Press OK
to confirm.
3. Exit programming mode.
Note:
The “High end” and “Low end” trim can only be set if the
zone is assigned to at least one DMX channel.
High end
Set zones
Display type
Set zones
Zone 4
Channels 1,2,3
on DMX AABB-CCDD
Unassign?
Programming (continued)
Enable
RGB/CMY Config
Master R/L
