Lucent Technologies 4703US Reference Manual Download

Page: 6 / 80

Lucent Technologies Inc.

Manual

August 2000

Venus AT Command Reference Manual

AT Command Set

(continued)

Table 8. In Commands

The ATI11 results are listed on two screens. To get to the second screen, the user must hit any key. The following is
an example of the ATI11 results.

Description

Status

---------------

--------------------

Last Connection

56K

V.90

Initial Transmit Carrier Rate

28800

Initial Receive Carrier Rate

50000

49333

Final Transmit Carrier Rate

28800

Final Receive Carrier Rate

50000

49333

Protocol Negotiation Result

LAPM

Data Compression Result

V42bis

Estimated Noise Level

152

Receive Signal Poser Level (–dBm)

Transmit Signal Power Level (–dBm)

Round Trip Delay (msec)

Press any key to continue; ESC to quit

Description

Status

---------------

--------------------

Near Echo Level (

–

dBm)

Far Echo Level (

–

dBm)

Transmit Frame Count

Transmit Frame Error Count

Receive Frame Count

Receive Frame Error Count

Retrain by Local Modem

Retrain by Remote Modem

Rate Renegotiation by Local Modem

Rate Renegotiation by Remote Modem

Call Termination Cause

Robbed-Bit Signalling

Digital Loss (dB)

Remote Server ID

4342C3

Last PCM S PTR

Command

Function

I0, I3

Returns modem identity string and driver version number (default).

Calculates a ROM checksum and displays it on the DTE.

Performs a ROM check, calculates the checksum, and then verifies the checksum by display-
ing OK or ERROR.

Returns firmware version for the data pump.

Returns the code version, board ID, and country ID in hexadecimal.

I6, I7, I8

Returns OK for compatibility.

Returns country ID in English.

I11

Displays connection information as described below.

Summary of Contents for 4703US

















































































Search results

Summary of Contents for 4703US

Reviews:

Related manuals for 4703US

Brands by name

Popular brands

Lucent Technologies 4703US, Reference Manual

Search results

Summary of Contents for 4703US

Reviews:

Related manuals for 4703US

Brands by name

Popular brands