Lucent Technologies 4703US Reference Manual Download

Page: 42 / 80

Lucent Technologies Inc.

Manual

August 2000

Venus AT Command Reference Manual

S-Registers

(continued)

S90—Read-Only Local Phone

This register tells the status of the local phone. It is read-only.

■

0 = on-hook.

■

1 = off-hook.

S91—Line Transmit Level

■

Range: 6—25 (corresponding to –6 dBm to –25 dBm transmit level)

■

Default: 10 (–10 dBm transmit level)

■

Units: –dBm

S109—V.PCM Connection Options

This register controls the connection type. Either V.90, K56flex, or both may be enabled.

Note:

The downstream connection rate is determined by the S38.

■

Range: 0—2

■

Default: 1

Table 72. Register S109

Value

Description

S109 = 0

K56flex connections possible (V.90 is disabled).

S109 = 1

Either V.90 or K56flex connections are possible (default).

S109 = 2

V.90 connections only.

Summary of Contents for 4703US

















































































Search results

Summary of Contents for 4703US

Reviews:

Related manuals for 4703US

Brands by name

Popular brands

Lucent Technologies 4703US, Reference Manual

Search results

Summary of Contents for 4703US

Reviews:

Related manuals for 4703US

Brands by name

Popular brands