LRX VULTURE User Manual Download Page 13 | Manualshive

Page: 13 / 21

background image

LRX

VULTURE

Check for the latest manual updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

11

11

Start UP – Press the “ON/OFF” key once.

The system will check the encoders and prepare the unit for operation. The user
does not have to press “OK or START” as the Vulture will pause for a short time,
then continue running if no key is pressed.

Normal Operating Display

The current MODE and DMX CHANNEL are displayed.
If valid DMX data is being received, the DMX channel will be green. If there is no
DMX data, the number will be red and crossed out.
Information on AC and BATTERY LEVEL / CHARGING is also displayed.

«
...
11
12
13
14
15
...
»

Summary of Contents for VULTURE






















Reviews:

No comments

Related manuals for VULTURE

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Brand: B. Braun Pages: 2

Aesculap Neurosurgery

Brand: B. Braun Pages: 13

Aesculap AdTec mini

Brand: B. Braun Pages: 2

Brand: B.Well Pages: 2

Brand: B. Braun Pages: 55

BA Ultimate LED

Brand: B.A. International Pages: 234

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

SC 2 Deluxe EasyFix

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 16

Brand: M-Audio Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands