manualshive.com logo in svg

Lord MicroStrain G-Link-LXRS, User Manual

Share
Download
Lord MicroStrain G-Link-LXRS User Manual Download Page 35

G-Link

®

-LXRS

®

Wireless Accelerometer Node

User Manual

Powering the Node

35

5.3

Charging the Node Battery

Use only the power supply specified for the node to charge

the battery.  Using a power supply above the rated voltage

could cause personal injury and permanent damage to the

node. For important safety considerations

see Safety

Information on page 64

.

NOTE

Touching sensors or charging the node battery while acquiring data may induce

noise on sensitive sensor signals and is not recommended.

1. Turn the node power switch off, and plug the node power supply into the node and

then into a 120/240VAC, 50/60Hz AC power source. Use only the power supply

specified for the node. Use the supplied power plug adapters, as needed.

2. Monitor the status of the charge indicators. For indicator meaning

see Device Status

Indicators on page 48

. Continue charging until the indicator turns green to indicate a

completed charge. Charging takes approximately 6-8 hours from a full depletion. 

Figure 26 - Node Charging

Summary of Contents for G-Link-LXRS








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands