LORCH MicorMIG 300 Page 49 Service Manual Download

Page: 49 / 68

page 49

PE (Protective Earth) -Protection

The PE monitoring is a standard feature in every machine. As soon as a current >15A is

flowing via the PE wire of the mains cable, a reed-contact opens up and the machine stops with

E04-01

PE-moni-

toring.

Schematic

DRV

DSP

X15-1

X15-2

-Uz

+3.3V

Cooling unit

Since January 14th 2016 the water cooled machines of the MicorMIG series are equiped with a water monitoring.

A sensor is mounted in the water tank, that is washed around by the cooling water of the return-flow. The sensor

is a “self-heating” sensor: the temperature is decreasing as soon as the water is flowing over it. If the water is not

flowing, the temperature of the sensor is kept stable.

If the pump is running and a flow of the water cannot be detected for longer than seven seconds, the machine

stops with the error message

E05

Schematic

SF27

X8-1
X8-3

MAPRO

X6-1

X6-2

X6-1

X6-2

DSP

tank

pump

hose connector blue

hose connector red

cooler

sensor

Since November 2017 with the software release 2.09 the water surveilance time was enhanced from

7 seconds to 10 seconds.

Summary of Contents for MicorMIG 300





































































Search results

Summary of Contents for MicorMIG 300

Reviews:

Related manuals for MicorMIG 300

Brands by name

Popular brands

LORCH MicorMIG 300, Service Manual

Search results

Summary of Contents for MicorMIG 300

Reviews:

Related manuals for MicorMIG 300

Brands by name

Popular brands