LORCH MicorMIG 300 Page 61 Service Manual Download

Page: 61 / 68

page 61

Measuring CAN bus

The CAN bus is easily checked at each pc-board by measuring the resistance value between CAN-low and

CAN-high against GND (ground). Before measuring, disconnect the pc-board completely from the machine.

If the measuring result is too low (1k ohm or lower), the CAN controller chip is damaged and the pc-board must be

exchanged.

Measuring the CAN bus at the MAPRO

Result: about 60k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the front panel

Result: 50k ohm - 60k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the DMR-RT3

Result: about 490k ohm each

CAN_LOW

GND

CAN_HIGH

Measuring the CAN bus at the DMRPP05 (Push-Pull DMR) is different, there the result is about 0.9k

ohm by standard. A faulty CAN controller chip may not be directly detecable.

Since week12 2017, CAN controllers with a higher dielectric strength are used on all pc-boards.

Summary of Contents for MicorMIG 300





































































Search results

Summary of Contents for MicorMIG 300

Reviews:

Related manuals for MicorMIG 300

Brands by name

Popular brands

LORCH MicorMIG 300, Service Manual

Search results

Summary of Contents for MicorMIG 300

Reviews:

Related manuals for MicorMIG 300

Brands by name

Popular brands