background image

16 

 

8    Annex 

8.2   Manufacturer’s Declaration 

 

The Manufacturer 
according to the EC 
regulations 

Henkel Loctite Deutschland GmbH 

Arabellastraße 17 
D-81925 München

 

declares that the unit designated in the following is, as a result of its design and 
construction, in accordance with the European regulations, harmonized standards and 
national standards listed below. 

Designation of the unit 

VoluDrop Dispenser UV 

Unit number 

97650 

Applicable EC Regulations  EC-Machine Directive 98/37/EEC 

Applicable harmonized 
standards 

DIN EN 292 Part 1; DIN EN 292 Part 2 11.1991 

Date / Manufacturer’s signature 

 

 

 

12/06/2002

 

Information 

regarding 

the 

Signer 

General 

Manager 

 

        (F. 

Löhr) 

 

 

For changes to the unit that were not approved by Loctite, this declaration loses 

its validity. 

8.3   Warranty 

(excluding Germany)

 

   

Loctite expressly warrants that all products referred to in this Operating Manual under VoluDrop Dispenser 
97650 (hereafter called “Products”) shall be free from defects in materials and workmanship. Loctite’s liability 
shall be limited, at its option, to replacing those Products which are shown to be defective either in materials 
or workmanship or to credit to the purchaser the amount of the purchase price thereof (plus freight and 
insurance charges paid therefore by the user). The purchaser’s sole and exclusive remedy for breach or 
warranty shall be such replacement or credit. A claim of defect in materials or workmanship in any Products 
shall be allowed only when it is submitted to Loctite in writing within one month after discovery of the defect 
or after the time the defect should reasonably have been discovered [and in any event within six months 
after the delivery of the Products to the purchaser]. No such claim shall be allowed in respect of Products 
which have been neglected or improperly stored, transported, handled, installed, connected, operated, used 
or maintained or in the event of unauthorized modification or the Products [including, where products, parts 
or attachments for use in connection with the Products are available from Loctite, the use of products, parts 
or attachments which are not manufactured by Loctite.] 
No Products shall be returned to Loctite for any reason without Loctite’s prior written approval. Products shall 
be returned freight prepaid, in accordance with Loctite’s instructions. 
EXCEPT FOR THE EXPRESS WARRANTY CONTAINED IN THIS SECTION, LOCTITE MAKES NO 
WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE 
PRODUCTS. 
ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND OTHER 
WARRANTIES OF WHATEVER KIND (INCLUDING AGAINST PATENT OR TRADEMARK 
INFRINGEMENT) ARE HEREBY DISCLAIMED BY LOCTITE AND WAIVED BY THE PURCHASER. 
THIS SECTION SETS FORTH EXCLUSIVELY ALL OF LOCTITE’S LIABILITY TO THE PURCHASER IN 
CONTRACT, IN PART OR OTHERWISE IN THE EVENT OF DEFECTIVE PRODUCTS. 
WITHOUT LIMITATION OF THE FOREGOING, TO THE FULLEST EXTENT POSSIBLE UNDER 
APPLICABLE LAWS, LOCTITE EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY 
DAMAGES INCURRED DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SALE OR USE OF, OR 
OTHERWISE IN CONNECTION WITH, THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, LOSS OF 
PROFITS AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER CAUSED BY 
LOCTITE’S NEGLIGENCE OR OTHERWISE. 

Summary of Contents for VoluDrop UV 97650



















Reviews: