background image

9

Phillips Head Screw

Alkaline Batteries
4 AA Type

Thumbturn

Status Indicator

Battery Cover

Speaker Hole

 

Lockout Mode

Low Battery

Indicator

Numbers

Touchscreen

 P  Key
(Return to Previous)

Privacy Mode Button

PROGRAMMING

Programming Features-Menus-Keys-Definitions ________________________________________9
Operation ________________________________________________________________________11

Programming Features - Menus - Keys - Definitions

Outside

Inside

Menu and Icons Used in This Guide

Press the indicated number

Enter Master PIN code (4-8 digits in length).

 

Press the   on the keypad to Enter or Accept entry.

 

Enter User PIN. Can be 4-8 digits in length.

Press the   Key to enter the Menu mode.

Manage User Codes (1-25);

RF Network-Controlled (1-250).

Press the   Key to return to the previous step or 

menu setting.

Complete

Continue

4

5

Register 

Continue

Complete

User Number (UN)

      1~25 : without network modile

      1~250 : with network module

Delete

Enable

Disable

Default settings

Automatic Re-lock

Inside Indicator Light

One Touch Locking

Enable

Disable

Enable

Continue

Register User PIN

Default settings

in 

bold.

Advanced Lock Settings

Volume Setting

Failsafe 9 volt

Battery Connection

(Use Alkaline battery)

Summary of Contents for Digital Deadbolt






















Reviews: