background image

 

 

1.0

 

INTRODUCTION 

 

 

The LBT is a thermal store for use with Renewable energy to provide a store of energy. 

 

All installations must conform to the relevant Building Regulations.  Health & Safety requirements must also be 
taken into account when installing any equipment.  Failure to comply with the above may lead to prosecution. 

 

If  the  equipment  is  to  be  connected  to  a  pressurised  system,  care  must  be  taken  to  ensure  all  extra  safety 
requirements are satisfied should a high or low-pressure condition occur in the system. 

 

2.0

 

SAFETY GUIDELINES 

 
Carefully read all the instructions before commencing installation. 
Keep these instructions near the water heater for quick reference. 
 

A  competent  person  must install  this  equipment.  All  installations  must conform  to  the  relevant  Building  Regulations. 
Health  &  Safety  requirements must  also  be  taken  into account when installing any equipment.  Failure to comply with the 
above may lead to prosecution.

 

Commissioning, maintenance and repair must be done by a skilled installer/engineer, according to all applicable standards 
and regulations. 
 

2.1

 

General description of safety symbols used 

 

 

BANNED 

A black symbol inside a red circle with a red diagonal indicates an action that should not be performed 

 

 

 

WARNING 

A black symbol added to a yellow triangle with black edges indicates danger 

 

 

 

ACTION REQUIRED 

A white symbol inserted in a blue circle indicates an action that must be taken to avoid risk 

 

 

This symbol shows essential information which is not safety related 

 

2.2

 

General  

 

 

Lochinvar  Limited  is  not  liable  for  any  damage  caused  by  inaccurately  following  these  mounting 
instructions. Only original parts may be used when carrying out any repair or service work. 

 

 

This  appliance  is not  intended  for use  by persons  (including children)  with  reduced physical, sensory  or 
mental  capabilities,  or  lack  of  experience  and  knowledge,  unless  they  have  been  given  supervision  or 
instruction concerning  use  of  the  appliance  by a  person  responsible  for their  safety.  Children  should be 
supervised to ensure that they do not play with the appliance. 

 

 

 

READ AND UNDERSTAND THE INSTRUCTIONS 

Read and fully understand all instructions before attempting to operate maintain or install the unit. 

Summary of Contents for LBT Series

















Reviews: