manualshive.com logo in svg

LNS Alpha 538, Instruction Manual

Share
Download
LNS Alpha 538 Instruction Manual Download Page 84

CHAPTER 8: OPERATION 

8-9 

ALPHA 538/552 

 

 

Part setup: Guiding channel 

 
Guiding channel 

The diameter of the guiding elements is always 
proposed for change after the pusher changeover 
cycle. 

 

Part setup: Number of clamping device openings 

 

Number of clamping device openings 

Number of lathe clamping openings during the 
machining of one part. Used to prevent undesired 
part feed out during clamping opening. 
 

 

Part setup: Alarm headstock reverse 

 
If the bar stock goes backwards when the lathe 
clamping device is open, an alarm is activated. 
 
This parameter has to be deactivated if a stopper 
is used to positioning the bar stock. 

 

5.3.  Application parameters 

Application: Part feed out with turret 

 

Defines if the lathe turret waits in position or 
follows the bar stock displacement during feeding 
operation. 

 

Summary of Contents for Alpha 538




















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands