manualshive.com logo in svg

LNS Alpha 538, Instruction Manual

Share
Download
LNS Alpha 538 Instruction Manual Download Page 103

CHAPTER 9: MALFUNCTIONS 

9-8 

 

  ALPHA 538/552 

 
 

AL19: Bar stock insertion malfunction! 

 

Description 

The "bar stock insertion malfunction" alarm is 
generated whenever the collet or material 
diameters are not adapted. 

 
Solutions 

Check the collet diameter. 
Check the bar stock loading diameter. 

 

 

 

 

AL20: Bar stock not extracted from the collet! 

 

Description 

The "Bar stock not extracted from the collet" alarm 
is generated if the signal (X25 

– SQ16) is not 

detected after the bar has been extracted from the 
collet of the bar feed.  Before the guiding channel 
opens to load a new bar, the remnant check 
device confirms that the remnant has been 
extracted from the collet of the bar feed.

 

 
Solutions 

Check that the extraction device jaws are not 
broken. 
Check the adjustment of SQ16, the switch should 
only activate when no bar is present in the collet 
of the bar feed. 
 
Contact LNS SA for further information. 

 

 

AL21: Bar stock magazine empty! 

 

Description 

This alarm is generated when no material is 
detected in the guidance zone. 

 
Solution 

Check the material presence. 

 

 

 

 

Summary of Contents for Alpha 538




















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands