LNS Alpha 538 Instruction Manual Download Page 68

Page: 68 / 115

CHAPTER 7: OPERATION

7-9

ALPHA 538/552

3.4. TUBES

The front tubes function as an extension of guiding channel, while protecting the zone between the
barfeed and the lathe.

Fixed tube

Telescope / Telescopic tube

3.5. Fixed tube (fixed headstock)

The front tube is a tube with fixed length. It serves specifically for fixed type lathe.

3.6. Telescopic tube (sliding headstock)

The telescopic tube can extend and retract. It

’s designed specifically for Swiss type lathe since the

spindle is sliding during the part feed out and the machining. Matching reduction tubes are mounted
inside of the telescopic tube to guide the bar and the pusher.

Article No

Internal ø

Retracted length

Maximum Stroke

042.037.013

48mm

178mm

384mm

042.037.073

42mm

240mm

580mm

332.037.053

42mm

225mm

530mm

332.037.023

42mm

165mm

348mm

Stretched

Retracted

Summary of Contents for Alpha 538




















































































































Search results

Summary of Contents for Alpha 538

Reviews:

Brands by name

Popular brands

LNS Alpha 538, Instruction Manual

Search results

Summary of Contents for Alpha 538

Reviews:

Brands by name

Popular brands