manualshive.com logo in svg

Lionel 2269W B & O Diesel Freight, Owner'S Manual

Share
Download
Lionel 2269W B & O Diesel Freight Owner'S Manual Download Page 27

Maintaining and servicing your set

27

Replacing your powered F3A unit’s lamps

Y

our F3A unit is illuminated by two 14-volt lamps. One illuminates the headlamp and the
other illuminates the cab interior. During the course of normal operation, they may require

replacement.

1. Remove the front screw on the underside of the frame and lift the body up slightly, pulling it

forward to release the two rear clips from the frame slots.

2. Carefully pull the bulb straight up out of the holder to remove it. Refer to Figure 7.
3. Replace the expired lamp with Lionel part no. 610-4584-300, available from your local

Lionel Authorized Service Center or Lionel Service. (For more information, see Lionel
Service on page 40.)

4. `Insert the replacement bulb and holder into the socket, making sure of a tight connection.

To reinstall the shell, first insert the rear tabs on the body into the slots on the frame. Line
up the screw holes on the frame and body shell, and reinsert the screw. Make sure all of the
wires are inside the body before you tighten the screw.

Make sure to insert the rear tabs on the body
into the slots on the frame before inserting
the front screw.

Lionel part no. 610-4584-300

Note!

Press AUX2 to make sure headlamps were not accidently turned off, before replacing
bulbs.

Note!

Press AUX1-9 to make sure cab lights were not accidently turned off, before
replacing bulbs.

Figure 7. Lamp replacement

Summary of Contents for 2269W B & O Diesel Freight









































Reviews:

No comments

Brands by name

Popular brands

Load more brands