Lionel 2269W B & O Diesel Freight Owner'S Manual Download | Manualshive

Page: 10 / 40

background image

RailSounds 5.0 sound system operations

Installing the battery

W

hile the RailSounds sound system is powered through the track, we recommend that you
install a nine-volt alkaline battery in the non-powered B-unit locomotive to prevent the

sound system from shutting down during track power interruptions (for example, at a switch or
a dirty section of track). Follow these steps and refer to Figure 3 as you install the battery.

If the RailSounds sound system turns off during interruptions in track power, you
may need to replace the battery.

1. Remove the screws on each end of the non-powered B-unit and lift the body off the frame..

2. Snap the battery into the battery clip on the circuit board.

3. Replace the body, securing it with the two screws.

10

Note!

Figure 3. Battery installation (non-powered B-unit locomotive only)

Volume adjustment knob

Front radiator fan
on F3B

«
...
8
9
10
11
12
...
»

Summary of Contents for 2269W B & O Diesel Freight









































Reviews:

No comments

Related manuals for 2269W B & O Diesel Freight

Brand: Zippkits Pages: 26

Brand: Gayla Pages: 2

Brand: LaTrax Pages: 11

Zoom EKA-3 Skywarrior interior

Brand: Eduard Pages: 3

Brand: K'Nex Pages: 28

Brand: Carrera RC Pages: 40

Lynx Mk.8 interior

Brand: Eduard Pages: 4

Brand: Ultrafly Pages: 16

Brand: marklin Pages: 12

My Real Jam Active Play Music

Brand: Little Tikes Pages: 2

Brand: Lionel Pages: 20

KID K’NEX 123 SEASAME STREET Ernie Building Set 85503

Brand: K'Nex Pages: 2

Mini Dual Deploy Screech

Brand: Madcow Rocketry Pages: 3

Antares C3M4 Combat Drone

Brand: Warlord Games Pages: 2

Thunderbolt Mini A10

Brand: J-Power Pages: 31

Brand: Fisher-Price Pages: 6

Brand: TTS Pages: 2

Brand: Faller Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands