background image

19

Lindab reserves the right to make changes without prior notice

2020-08-05

UltraLink Controller  

FTCU

lindab  |  we simplify construction

Lindab reserves the right to make changes without prior notice

2020-08-05

Technical data

Power supply

AC/DC

24 (19—28) V

Cable

Max outer diameter

7 mm

Power consumption

Dim. 100 - 315

2 W

Dim. 400 - 630

3 W

Power consumption

For wiring, dim. 100 - 315

3 VA

For wiring, dim. 400 - 630

5 VA

Premounted cable

Length

0,7 m

IP class

42

Tightness class to the environment

EN 12237

D

Tightness class, past a closed damper

EN 1751

4

Pressure class, closed damper

Dim. 100 - 315

C (max 5000 Pa)

Dim. 400 - 630

B (max 2500 Pa)

Storage temperature range

-30 to +50 °C

Maximum ambient moisture

95 % RH

Connection

RS485 standard or analog

Cable

RS485 standard cable, 2-wire shielded 
twisted pair, min. 0,1 mm² (LIYCY cable)

Protocol

Modbus

Output

Flow
Flow
Velocity
Temperature
Damper position (0% fully closed, 100% 
fully open)

m³/h
l/s
m/s
°C
%

Velocity range

For guaranteed measurement uncertainty

0,2 — 15,0 m/s

Measurement uncertainty, flow 
(min. 5 diamters of straight duct before the  
UltraLink.)

Depending on which is the greatest of the 
percentage or the absolute value for the 
specific product size.

±5 

Dim. 100 = ±1,00 
Dim. 125 = ±1,25 
Dim. 160 = ±1,60 

Dim. 200 = ±2,00 
Dim. 250 = ±2,50 

Dim. 315 = ±3,15

Dim. 400 = ±4,00
Dim. 500 = ±5,00
Dim. 630 = ±6,30

% or 
l/s 
l/s 
l/s 
l/s 
l/s 
l/s
l/s
l/s
l/s

Temperature range

-10 to +50 °C

Measurement uncertainty, temperature

±1 °C

Screws on lid of display unit

Philips (PH1)

4 pcs

Bluetooth radio

Frequency

2402 — 2480 MHz

Output power

-40 to +9 dB

Summary of Contents for UltraLink FTCU

























Reviews: