Lincoln IMPINGER 1162 Operating Instructions Manual Download Page 5

Page Number - 5

Form 420110

AUTOMATIC AIR GREASE GUN

MODEL 1162

TO CONVERT GUN TO ALLOW FILLING FROM

BULK CONTAINER OR FILLER PUMP

1)  Unscrew the container cap from the container tube. Pull 

  on the follower handle to extract the follower and spring

  from the container tube.

2)  Grasp follower between thumb and forefinger and flip the

  follower lip from the rear to the front side.

NOTE:   The follower resembles a cup. When the gun is

   

assembled for use with bulk lubricant, the cup 

   

opens toward the head assembly.

3)  Reassemble follower into container tube and position

  with the follower handle so that the container cap can be

  tightened onto the container tube. 

Fig. 3

TO FILL THE GUN FROM BULK CONTAINER

1)  Remove head and plunger assembly from container 

  tube.

2)  Pack lubricant into cavity of the head and plunger 

  assembly.

3)  Insert the open end of the container tube into lubricant.

  Slowly pull the follower handle back while pushing the

  container tube deeper into the lubricant to prevent air

  pockets from being pulled into the container tube.

4)  When the follower rod is fully extended, pull it

 

sideways 

  to latch the rod groove into the keyhole slot in the 

  container cap.

5)  Loosely assemble the head and plunger assembly to the

  filled container tube. Release the follower rod from the

  container cap and disengage the follower rod from the

  follower by rotating the follower handle. Push the follower

  rod into the container. Slowly unscrew the container tube

  from the head and plunger assembly until lubricant 

  oozes from the interface. Tighten container tube into the 

  head and plunger assembly.

TO FILL THE GUN WITH A FILLER PUMP

Engage the follower rod with the follower by rotating the

follower handle. Insert the gun filler nipple into the filler

pump socket. Operate the filler pump to fill the container.

When the follower rod groove is exposed, the container is

filled (follower rod will be extended approximately 8 inches

or 20 cm).  Disengage the follower rod from the follower by 

rotating the follower handle. Push the follower rod into 

the container.

 

Fig. 4

Fig. 5

TO EXPEL AIR POCKETS

1)  Withdraw the follower rod from the grease tube 

 

assembly cap and engage it with the follower by rotating 

the follower handle . Exert the force on the follower handle 

after opening the vent/filler fitting (18) (see Fig. 6).

2)  Pull the trigger in short bursts to operate gun until trapped 

air is expelled. Disengage the follower rod from the fol-

lower by rotation the follower handle. Push the follower 

rod into the grease tube assembly.

3)  If the step 2 fails, unscrew the grease tube assembly1-1/2 

turns from the pump assembly.

4)  Exert force on the follower handle until lubricant oozes 

 

from the grease tube assembly and pump assembly  

 

interface.

5)  Tighten grease tube assembly into the pump assembly.

 

Disengage the follower rod from the follower by rotation

 

the follower handle. Push the follower rod into the grease 

tube assembly.

Summary of Contents for IMPINGER 1162































Reviews: