Lincoln IMPINGER 1162 Operating Instructions Manual Download Page 4

Page Number - 4

AUTOMATIC AIR GREASE GUN

MODEL 1162

Form 420110

APPROPRIATE USE

·  The Air Gun was exclusively designed to pump and 

  dispense lubricant using pneumatic power.

·  The maximum specification rating should not be 

  exceeded.

·  Any other use not in accordance with instruction will 

  result in loss of claim for warranty or liability.

SPECIFICATIONS

Pump ratio (max)   

 

40:1

Output per stroke  

 

.038 in³ (0.62 cm³)

Pneumatic Inlet pressure (min) 

40 Psig (2.7 Bar)

 

 

 

(max)  150 Psig (10.3Bar)

Grease output pressure (max) 

6,000 Psig (414 Bar)

Grease reservoir capacity   

14.5 oz (450 cm³)

Operating temperature range 

0 to 120 °F(-18 to +50°C)

Weight (empty)   

 

4.5 Lbs. (2.0 Kg)  

Weight (full)  

 

 

5.5 Lbs. (2.5 Kg)

Lubricant up to NLGI 

 

#2 Grease

Pneumatic port inlet  

 

1/4-18 NPSF

Grease Port Outlet 

 

7/16-28 UNEF

WORK AREA

Keep bystanders, children, and visitors away while

operating. Distractions can cause you to make mistakes.

INSPECTION

Visually inspect for damaged, loose or missing parts. If

equipment is worn or damaged, remove from service.

Contact an authorized service center for damage

assessment or repair.

OPERATION

Prime the Air Grease Gun after each refill or grease 

cartridge change. Prime the gun before using it to lubricate 

grease points.

For optimum performance and product life, add a few drops of 

lubricating oil (SAE 30 or greater) through the air fitting at the 

bottom of the handle if gun begins to cycle slowly or erratically.

To prime, operate the gun slowly, by gently throttling the trigger 

(8), until grease flows from the open end of the hose.  The 

vent/filler valve (18) should be used to expel air pockets.  This 

is done by loosening the vent/filler valve a couple of turns, 

holding the gun with the discharge hose pointing up, and al-

lowing the air to escape.  Close the vent/filler valve after air 

is removed.  If a prime can not be achieved after the gun has 

operated for 10-15 seconds, see the section “TO EXPEL AIR 

POCKETS”.

 

The gun will stall if a bearing or fitting is blocked, causing the 

grease pressure to rise to maximum.  A blocked bearing or fit

-

ting should be corrected before continuing lubrication.

Air pockets in the cartridge lubricant will cause the gun to 

lose prime.

REMOVING EMPTY GREASE CARTRIDGE

1)  Pull back on the follower handle until the follower 

 

rod is fully extended and latch the follower rod 

 

groove into the slot on the tube cap.

2)  Unscrew the grease tube assembly from the gun.

3)  Carefully release the follower handle to the eject

 

the empty cartridge from container tube.

INSTALLATION GREASE CARTRIDGE

1)  Visually check the follower seal lip direction before

 

loading a new cartridge. The follower seal lip must be

 

directed toward handle or rear side for cartridge 

 

loading.  To change the direction of the follower seal, 

 

unscrew tube cap from grease tube assembly and pull on 

the handle to remove follower seal from tube. Flip follower 

seal over and reassemble.

2)  Pull back on the follower handle and latch the 

 

follower rod groove into the slot on the tube cap.

3)  Remove the plastic cap from the grease cartridge

 

and insert cartridge into container tube.

4)  Remove the pull tab from the grease cartridge

 

and screw grease tube assembly into pump assembly.

5)  Release follower rod from slot.  Purge air from pump.

 

See air purging instruction.

©

©

© Indicates change

Summary of Contents for IMPINGER 1162































Reviews: