background image

FUEL

Fill  the  fuel  tank  with  clean,  fresh,  lead-free  gasoline.
Observe  fuel  sight  gauge  in  the  base  of  the  machine
while filling to prevent overfilling.

OIL

The EAGLE™ 10,000 Plus is shipped with the engine
crankcase  filled  with  SAE  10W-30  oil.  Check  the  oil
level before starting the engine. If it is not up to the full
mark  on  the  dip  stick,  add  oil  as  required.  Make  cer-
tain that the oil filler cap is tightened securely. Refer to
the engine Owner’s Manual for specific oil recommen-
dations.

BATTERY CONNECTIONS

Use  caution  as  the  electrolyte  is  a  strong
acid that can burn skin and damage eyes.

------------------------------------------------------------------------

This welder is shipped with the negative battery cable
disconnected. Make sure that the Engine Switch is in
the  “STOP”  position  and  attach  the  disconnected
cable securely to the negative battery terminal before
attempting  to  operate  the  machine.  If  the  battery  is
discharged and does not have enough power to start
the engine, see the battery charging instructions in the
Battery section.

NOTE

:  This  machine  is  furnished  with  a  wet  charged

battery; if unused for several months, the battery may
require a booster charge. Be careful to charge the bat-
tery with the correct polarity.

3. Proper placement of the equipment on the trailer to

insure stability side to side and front to back when
being  moved  and  when  standing  by  itself  while
being operated  or serviced.

4. Typical  conditions  of  use,  i.e.,  travel  speed;  rough-

ness of surface on which the trailer will be operated;
environmental conditions.

5. Conformance with federal, state and local laws

(1)

(1) Consult applicable federal, state and local laws regarding specific

requirements for use on public highways.

A-3

INSTALLATION   

EAGLE™ 10,000 PLUS

A-3

PRE-OPERATION SERVICE

READ  the  engine  operating  and  maintenance
instructions supplied with this machine.

CAUTION

LUBRICATION  SYSTEM  CAPACITY

(INCLUDING  FILTER)

Kohler CH23S - 2.0 Quarts (1.9 Liters)

•   Damage to the fuel tank may cause

fire or explosion.  Do not drill holes
in the EAGLE™ 10,000 Plus base or
weld to the EAGLE™ 10,000 Plus
base.

-----------------------------------------------------------------------

WARNING

CAUTION

• Stop engine while fueling.
• Do not smoke when fueling.
• Keep sparks and flame away  from

tank.

• Do  not  leave  unattended  while

fueling.

• Wipe  up  spilled  fuel  and  allow

fumes  to  clear  before  starting
engine.

• Do  not  overfill  tank,  fuel  expan-

sion may cause overflow.

GASOLINE FUEL ONLY

------------------------------------------------------------------------

WARNING

GASOLINE

can cause fire
or explosion.

VEHICLE MOUNTING

Improperly  mounted  concentrated  loads  may
cause unstable vehicle handling and tires or other
components to fail.

• Only  transport  this  Equipment  on  serviceable

vehicles which  are  rated and  designed  for  such
loads.

• Distribute,  balance  and  secure  loads  so  vehicle

is stable under conditions of use.

• Do not exceed maximum rated loads for compo-

nents such as suspension, axles and tires.

• Mount equipment base to metal bed or frame of

vehicle.

• Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------

WARNING

Summary of Contents for 000 PLUS IM10028-B





































Reviews: