background image

EU DECLARATION OF CONFORMITY

Manufacturer’s Name:

Lighthouse Worldwide Solutions, Inc.

Manufacturer’s Address:

Lighthouse Worldwide Solutions, Inc.
1221 Disk Drive
Medford, OR  97501  USA

Declares that the product:

Product Name:

Remote Airborne Particle Counter

Model Number(s):

REMOTE 3012PN, 3102PN, 5012PN, 5102PN, 50102PN

Conforms to the following Product Specifications:

SAFETY

EN61010-1:2001

Safety Requirements for Electrical Equipment for 

Measurement, Control, and Laboratory Use Part 1: 
General Requirements IEC 61010-1:2000

Safety Requirements for Electrical Equipment for 
Measurement, Control and Laboratory Use, Part 1: 
General Requirements

LASER SAFETY

Guidance on Laser Products: Conforms to FDA 21 CFR 
Chapter 1 Subchapter 1

EMC

EN61326

Electrical Equipment for Measurement, Control and 

Laboratory Use EMC Requirements Part 1: General 
Requirements Includes Amendment A1:1998; IEC 
61326:1997 + A1:1998

UL 61010A-1 - UL Standard for Safety Electrical Equipment for Laboratory Use; Part 1: General Requirements
Replaces UL 3101-1

Supplementary information

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC amended by 
Directive 93/68/EEC and the EMC Directive 89/336/EEC amended by Directive 93/68/EEC and carries the 
CE marking accordingly.

William Shade - V.P. Engineering

Fremont, CA. March 7, 2008

CAN/CSA C22.2
No. 1010.1-1992

IEC 60825-1 Am. 2
IEC 60601-2-22
(Laser Notice 50)

Summary of Contents for REMOTE 3012PN



























































Reviews: