background image

Warranty

The warranty for our products is 2 years. It comprises  any repair of failures – free of
charge – which can be proved to result from defects of fabrication.

Warranty expires when:

- the device was modified or attempted to be repaired
- damages were caused by the intervention of foreign persons
- damages are due to noncompliance with the operating instructions
- the device was connected to an incorrect voltage or incorrect type of current
- the device was incorrectly operated or when damages were caused by negligent 
   handling or misusage

All maintenance and servicing works related to the product   must be carried out by the
company 

Licht-Technik. Licht-Technik

 shall not assume any liability for losses or damages

of any kind being the results of inexpert servicing.

Further information

This document and the information contained therein are subject to copyright and neither
the  whole nor  any  part  of  it  may,  and   this  is also  valid  for the  described   product,   be
reproduced, copied or recorded in any form without the prior written authorization of 

Licht-

Technik Vertriebs GmbH

.

The   products   of  

Licht-Technik   GmbH

  are   subject   to   constant   development.  Therefore

Licht-Technik

  reserves   the   right   to   modify   components,   motors   and   also   technical

specifications any time and without prior notice.

12

Mix4-6 Rev.: 1.02

Summary of Contents for Mix4-6














Reviews: